cationic polyacrylamide emulsion Praestol K105L k110FL K120L can be replaced by Chinafloc EM
Praestol K105L k110FL K120L are three kinds of cationic polyacrylamide emuslion with lower and medium cationic charge ,mainly used for municipal and some industrial wastewater treatment,Chinafloc EM0510,.Chinafloc EM1012,Chinafloc EM3012 can replace of them totally with good result.
Cationic polypropanamide emulsion, in addition to the advantages of cationic polyacrylamide dry flocculant also has charge density selectivity, fast dissolution rate, low energy consumption, convenient transportation, easy storage and use. Compared with traditional products, cationic polyacrylamide emulsion is suitable for a wide range of PH values, cationic polyacrylamide emulsion, in addition to the advantages of cationic polyacrylamide dry flocculant but also has a large charge density optional, fast dissolution rate, low energy consumption, convenient transportation, storage and use of easy. Compared with traditional products, cationic polyacrylamide emulsion is suitable for a wide range of PH value, high charge stability, good flocculation effect, less dosage and a series of advantages. It is also suitable for the construction site without the installation of large dissolving device. Below, the small edition of cationic polyacrylamide to give you a brief introduction!
Application of cationic polyacrylamide emulsion:
Cationic polyacrylamide emulsion is widely used in a variety of domestic sewage, chemical wastewater, oilfield sewage, sludge dehydration treatment, paper and other fields, cationic polyacrylamide oil-water emulsion is widely used in urban domestic sewage treatment, brewery, amylery, food processing plant and other sewage treatment. It is especially suitable for flocculating sedimentation of organic suspended matter in acidic or slightly acidic sewage. Paper industry used as retention aid filter, paper sewage treatment. It can be used as oil removal agent in petroleum industry.
Cationic polyacrylamide emulsion use note:
1. Contact personnel shall wear protective equipment when using polyacrylamide, and skin contact parts shall be washed immediately with clean water.
2. The operation site should be cleaned in time to prevent slipping and falling.
Cationic polyacrylamide emulsion use process:
1, before the use of cationic polyacrylamide liquid product series, should be shaken as far as possible;
2. During the dissolving operation, add the product while adding water. The solution concentration is recommended to be controlled at 3-5 ‰, and the curing time is about 25 minutes.
3, avoid the use of centrifugal pump and other high shear rotor pump, the best use of screw pump, diaphragm pump and other low shear pump;
4. The dissolving operation should be carried out in the groove of plastic, ceramic, stainless steel and other materials. The stirring speed should not be too large, without heating.
5, the prepared dilute solution should not be long, good with the use of dissolution;
6, cationic polyacrylamide emulsion and inorganic coagulant compound use of wastewater treatment, should first add inorganic coagulant, to appear obvious alum, then add this product, can not reverse the order, also can not be joined at the same time.Cationic polypropanamide emulsion, in addition to the advantages of cationic polyacrylamide dry flocculant also has charge density selectivity, fast dissolution rate, low energy consumption, convenient transportation, easy storage and use. Compared with traditional products, cationic polyacrylamide emulsion is suitable for a wide range of PH values, cationic polyacrylamide emulsion, in addition to the advantages of cationic polyacrylamide dry flocculant but also has a large charge density optional, fast dissolution rate, low energy consumption, convenient transportation, storage and use of easy. Compared with traditional products, cationic polyacrylamide emulsion is suitable for a wide range of PH value, high charge stability, good flocculation effect, less dosage and a series of advantages. It is also suitable for the construction site without the installation of large dissolving device. Below, the small edition of cationic polyacrylamide to give you a brief introduction!
Application of cationic polyacrylamide emulsion:
Cationic polyacrylamide emulsion is widely used in a variety of domestic sewage, chemical wastewater, oilfield sewage, sludge dehydration treatment, paper and other fields, cationic polyacrylamide oil-water emulsion is widely used in urban domestic sewage treatment, brewery, amylery, food processing plant and other sewage treatment. It is especially suitable for flocculating sedimentation of organic suspended matter in acidic or slightly acidic sewage. Paper industry used as retention aid filter, paper sewage treatment. It can be used as oil removal agent in petroleum industry.
Cationic polyacrylamide emulsion use note:
1. Contact personnel shall wear protective equipment when using polyacrylamide, and skin contact parts shall be washed immediately with clean water.
2. The operation site should be cleaned in time to prevent slipping and falling.
Cationic polyacrylamide emulsion use process:
1, before the use of cationic polyacrylamide liquid product series, should be shaken as far as possible;
2. During the dissolving operation, add the product while adding water. The solution concentration is recommended to be controlled at 3-5 ‰, and the curing time is about 25 minutes.
3, avoid the use of centrifugal pump and other high shear rotor pump, the best use of screw pump, diaphragm pump and other low shear pump;
4. The dissolving operation should be carried out in the groove of plastic, ceramic, stainless steel and other materials. The stirring speed should not be too large, without heating.
5, the prepared dilute solution should not be long, good with the use of dissolution;
6, cationic polyacrylamide emulsion and inorganic coagulant compound use of wastewater treatment, should first add inorganic coagulant, to appear obvious alum, then add this product, can not reverse the order, also can not be joined at the same time.
Praestol K112L K128L K132L K133L K136L are kinds of cationic emuslion with medium r and high cationic charge mainly used for water treatment and sludge dewatering ,chinafloc EM2012 EM3012 EM4008 EM5008 EM6008 can replace of them totally with good performance.
Praestol K112L K128L K132L K133L K136L are kinds of cationic emuslion with medium r and high cationic charge mainly used for water treatment and sludge dewatering ,chinafloc EM2012 EM3012 EM4008 EM5008 EM6008 can replace of them totally with good performance.
Praestol K112L K128L K132L K133L K136L are kinds of cationic emuslion with medium r and high cationic charge mainly used for water treatment and sludge dewatering ,chinafloc EM2012 EM3012 EM4008 EM5008 EM6008 can replace of them totally with good performance.
